Pages

Saturday, September 28, 2013

Teardown: Black & Decker PD1200 Dustbuster Flexi partial teardown - Battery and charging circuit analyzed

Some month ago I bought a Black & Decker PD1200 Dustbuster Flexi Vacuum cleaner
The Dustbuster Flexi PD120, in all it's glory :-)
Now, the PD1200 is a nice object, useful, functional, well-working... It only has a tiny defect, I've nicknamend it "DarinFast" (a mockup english translation for the italian "ScaricoFacile")
When it was new, the battery lasted 9 minutes... now I'm not brave enough to check them again... but I know batteries are getting worse.

I would like to use it to clean my car... but 9 minutes are not enough...
So today I decided to take a look inside the PD1200, to see if I can find a way to use an external power supply (like a car cigarette lighter).

So here are some shot of a partially dismantled PD1200.
I just opened the lower part, with the battery and the charging circuit.
To open the lower part, you need to remove the 8 screw that hold it to the motor block.
After removing these 8 screws, the lower part can be opened, but it will also detach from the main motor block (so keep a eye on the parts, and don't let them fall on your feet :-) ).

Click the image to see them bigger, these are Full Res photos.

Battery and cable,
The 2 battery pack are connected in series, via the yellow cable.





 Detail of one battery pack, the black wire go straight to the motor.
 
The battery pack can be lifted

 Under the other battery pack you can find the charging circuit.
 

 Some more circuit images

 Lateral photo of the battery pack/circuit/cabling.

Here you can see the connection between the battery block and the motor block.
Kudos to the Black & Decker engineering team for using a detachable connector.

The detached motor block

The detached battery block

Now get to the interesting parts.
Here you can see a schema of the connections/wires
The first block on the left is the charging circuit, I considered it a "black box" :-)
The wire on the left are the external power connector of the PD1200.

The battery have an interesting connection scheme: the positive wire is always connected to the motor, and to the charging circuit.
The negative wire from the battery get connected to the motor only when you switch on the PD1200
When the PD1200 is switched off, the negative battery wire is connected to the negative wire from the charging circuit.
In the drawing you can see the "connector" that connect the battery block to the motor block.
And the switch (I draw it under the motor) with the 2 possible connection (1 when it's switched on, 0 when it's switched off)
 After looking at the connection scheme I've answered one of my question:
Question: Can I modify something so that the charging connector can be used even as an external power supply?
Answer: No! because the charging connector is not in any way directly connected to the battery, nor to the motor.. and the charging wire between the charging circuit and the battery are much smaller than the wire that power the motor.

So, the only way to use an external power supply is to add another connector.
It should be a connector that interrupt the negative wire from the battery when in use: this way I will be able to leave the positive wire from the new connector always connected to the motor, and still be able to use the switch to turn the engine on and off.

Now here is some photo of a corner of the battery pack, where I think I could place a new connector.



Now I know what I nee to buy to mod my PD1200... :-)

Update: The PD1200 motor is power hungry :-)
Today did some test to check the power requirement of the PD1200 motor.
I detached the battery block from the motor block, and I put a tester between the motor ant the battery, to measure the current used by the motor.
I must say that I'm surprised: the PD1200 consume up to 10A @ 12V
This mean that the PD1200 have a 120W motor.
Now I understand why the PD1200 battery drain so fast, with a discharge current of 10A no battery can last much...

The battery pack inside the PD1200 probably have a capacity around 2000 mAh, this is compatible with the measured discharge time of about 9/10 minutes.

The PD1200 consume the maximum current (10A) when the motor is running at the maximum speed, and it's sucking only air, without obstruction.
If you close the suction tube, the motor run at a higher RPM (because the air pressure get lower, so with the same power it can move faster) and also use less current: with the aspiration hole totally obstructed it require 'only' 6.5A.

Now I know that if I want to use an external power supply, it must be able to give 10A, and must use big enough cable (the cable of the tester I user to check the used current got hot in just some seconds...)

Saturday, September 14, 2013

Come scaricare la PEC di postacertificata.gov.it direttamente dentro Gmail

This post is in italian, because in Italy we have the so called PEC (a kind of certified email, more info there) so  the following information are relevant only for italian people.

Istruzioni:
Nei seguenti passaggi vi spiegherò come poter configurare il vostro account Gmail per scaricare la vostra Posta Elettronica Certificata dal sito postacertificata.gov.it , così troverete le vostre PEC assieme alle altre email e potrete leggerle comodamente.

1) Entrate nel vostro account Gmail

2) Aprite le impostazioni (vedi immagine)


3) Andate nella sezione "account"  (vedi immagine)


4) Cliccate la voce "Aggiungi un tuo account di posta POP3" (vedi immagine)

5) Si aprirà una finestrella come la seguente, inserite il vostro indirizzo PEC, ad esempio  pincopallo@postacertificata.gov.it

 poi andate al passaggio successivo


6) Ora avrete una finestra come la seguente
 compilate tutti i campi:
*) campo Nome utente : inserite il vostro indirizzo PEC (per esempio pincopallo@postacertificata.gov.it)
*) campo Password : inserite la password della vostra PEC
*) campo Server POP : inserite mail.postacertificata.gov.it  (alle volte è già inserito, nel qual caso va bene così)
*) campo Porta : mettete il valore 995

*) SPUNTATE il campo "Lascia una copia del messaggio scaricato sul server" (così vi resterà una copia della vostra PEC sui server di postacertificata.gov.it )

Salvate le modifiche e passate alla schermata successiva

7) Troverete una schermata come la seguente
Selezionate la voce NO
e cliccate Fine

8) Finito :-)
Ora il vostro account Gmail provvederà a scaricare automaticamente le vostre PEC, così le troverete assieme alle vostre altre email, e potrete leggerle direttamente dentro al vostro account Gmail.

IMPORTANTE:  Se vi scade la password della PEC, o se la modificate, GMail non riuscirà più a scaricare le vostre PEC. Quindi dovrete tornare nelle impostazioni, ed aggiornare la password con quella corretta.

Per aggiornare la password dovrete tornare nelle impostazioni (vedi passo 4),
poi dovrete cliccare la voce "modifica informazioni" (vedi immagine)


a questo punto vi ritroverete in una schermata come la seguente


Cliccate su "modifica password", inserite la password nuova, e salvate le modifiche.
Così Gmail  riprenderà a scaricare le vostre PEC.